Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 18 (1836), p. 257 · View the page
100. For a House Warmer; O. Kindrick, and W. Elwell, Gardiner, Maine, February 25.
Remarks. A hollow box of iron is placed across the back of the fire place, with a tube from one end of it leading into a cellar, or other place, for a supply of cold air, the other end being furnished with a tube to conduct the heated air into the room; this latter tube is to pass to some distance up the chimney, where it is to be elbowed, so as to admit the heated air into the room; and the patentees say, "what we specifically claim as our improvement, and for which we ask an exclusive right, is the making of, and applying a box, cistern, or cockle, as above described, to a common fire place, fire frame, or stove, for the purpose of heating, or warming, rooms." This plan is equally old, and inefficient. Would it not be well to add a dog wheel, or some other motive power, to force air through the tube by means of a blowing apparatus? Progress of Physical Science. Formation of Ether. By M. MITSCHERLICH. The decomposition of alcohol into æther and water is not interesting merely by the production of æther, but is especially so as an example of a particular kind of decomposition, which cannot be so well followed with any other substance, and which is manifested in the formation of some important products, for example, in that of alcohol itself. M. Mitscherlich has endeavored to elucidate the phenomena of this decomposition by the following *22 experiments: Take a mixture of 100 parts of sulphuric acid, 20 of water, and 50 of anhydrous alcohol, and heat it gradually until its boiling-point becomes 284° Fahrenheit. Alcohol is then allowed to fall gradually into the vessel which contains the mixture, and the current is to be so regulated that the heat of the mixture remains constantly at 284°. If, for example, the operation be conducted with a mixture of six ounces of sulphuric acid, one ounce and one-fifth of water, and three of alcohol, and if the density of each two ounces of product as it is obtained be taken, it will be observed that this density passes gradually from 0.780 to 0.788 and 0.798, and afterwards remains constantly at the last mentioned density, which is exactly that of the alcohol employed. If the operation be properly conducted, an unlimited quantity of alcohol may be converted into æther, provided that the sulphuric acid does not change. The distilled liquor is formed of two distinct fluids; the upper one is æther, containing a little water and alcohol; the lower one is water with a little alcohol and æther. Its weight is nearly equal to that of the alcohol employed, and it is composed of Æther, Alcohol, Water, 65 18 17-100 If into six ounces of concentrated sulphuric acid six ounces of pure alcohol are suffered to flow gradually, a product of constant density is not obtained until the sulphuric acid has taken its proportion of water. Take, on the contrary, three ounces of sulphuric acid and two ounces of water, and let alcohol be added, drop by drop; the first two ounces distilled are merely spirit of wine, of specific gravity 0.926, containing scarcely a trace of æther. The density decreases until the quantity of water of the sulphuric acid is reduced to its proportion, and the product of the distillation has acquired the density of the alcohol. If concentrated sulphuric acid be added to anhydrous alcohol in excess, pure alcohol distils at first; but when the temperature reaches nearly 260° the first traces of æther begin to appear; the production of æther is at its maximum between 284º and 302°. It results from the preceding observations, that alcohol when in contact with sulphuric acid, is converted into æther and water at a temperature of about 284°. A great number of analagous decompositions and combinations are known which may be attributed entirely to the influence of the contact of bodies. The most remarkable example of this kind is that of the conversion of oxygenated water into water and oxygen, by the slightest trace of the peroxide of manganese and some other substances. The decomposition of sugar into alcohol and carbonic acid, the oxydizement of alcohol when it is changed into vinegar, are phenomena of the same kind; and so also is the conversion of starch into sugar by means of sulphuric acid. Μ. Mitscherlich, observing that in the preparation of carburetted hydrogen by means of sulphuric acid and alcohol, water is formed at the same time, attributes this decomposition of alcohol to the influence of mere contact, and not to the affinity of sulphuric acid for water. Journal de Pharmacie, Juin, 1835, & Lond. and Edin. Philos. Jour. "Report of Magnetic experiments tried on board an Iron Steam-Vessel, by order of the Right Hon. the Lords Commissioners of the Admiralty." By Edward J. Johnson, Esq., Commander, R. N., accompanied by plans of the vessel, and tables showing the horizontal deflection of the Magnetic needle at different positions on board, together with the dip and magnetic Hydraulic Lime. intensity observed at those positions, and compared with that obtained on shore with the same instruments. This report commences with a description of the iron steam-vessel, the "Garryowen," belonging to the city of Dublin Steam Packet Company, and built by the Messrs. Laird, of Liverpool. She is constructed of malleable iron, is 281 tons burthen, and draws only 54 feet water, although the weight of iron in the hull, machinery, &c. is 180 tons. The experiments having been interrupted by a continuance of wet and stormy weather, the author proceeds to draw the following general practical conclusions, deduced from the series of observations already made, and points out the further experiments which he considers necessary to be tried. 1st. The ordinary place for a steering-compass on board ship is not a proper position for it in an iron steam-vessel. 2nd. The binnacle-compass in its usual place on board the Garryowen is too much in error to be depended upon. 3rd. In selecting a proper position for a steering-compass on board iron steam-vessels, attention should be paid to its being placed, as far as is practicable, not only above the general mass of iron, but also above any smaller portions of iron that may be in its vicinity; or such portions of iron should be removed altogether. 4th. The steering-compass should never be placed on a level with the ends either of horizontal or perpendicular bars of iron. 5th. The extreme ends of an iron vessel are unfavorable positions, in consequence of the magnetic influences exerted in those situations. The centre of the vessel is also very objectionable, owing to the connecting rods, shafts, and other parts of the machinery belonging to the steam-engine and wheels, which are in continual motion; independently of the influence exerted by the great iron tunnel in this part of the ship. 6th. No favorable results were obtained by placing the compass either below the deck, or on a stage over the stern. 7th. It was found that at a position of 20 feet above the quarter-deck, and at another 134 feet above the level, and about one-seventh the length of the vessel from the stern, the deflections of the horizontal needle were less than those which have been observed in some of His Majesty's ships. The author proceeds to point out various methods of determining, by means of a more extended inquiry, whether the position above indicated, or one nearer to the deck, is that at which the steering-compass would be most advantageously placed. The concluding section contains an account of some observations made by the author on the effects of local attraction on board different steam-boats, from which it appears that the influence of this cause of deviation is more considerable than has been generally imagined; and he points out several precautions which should be observed in placing compasses on board such vessels. Proceedings Roy. Soc. Lond. and Edin. Philos. Mag. Hydraulic Lime. M. Vicat communicated a paper to the Royal Academy of Sciences at Paris, on the sole efficacy of magnesia in rendering certain limestones hydraulic. This paper has for its object the correction of an opinion given by M. Berthier in the Journal des Mines of 1832, that magnesia alone has no more efficacy than alumina to render lime hydraulic; from which it would follow that silex was the only essential principle in all cases. M. Vicat was for a long time of the same opinion, which he now declares i incorrect; and says that magnesia alone, when in sufficient quantity, will render pure lime hydraulic. He does not explain the degree of energy of these new species of lime, but only affirms that they will solidify from the 6th to the 8th day, and continue to harden in the same manner as ordinary hydraulic lime. Until his experiments are further advanced, he states that the proportions of magnesia taken and weighed after calcination, should be from 30 to 40 for every 40 of pure anhydrous lime. The native limestones examined and cited by M. Berthier contained only from 20 to 26 of magnesia for every 78 to 60 of lime: it is probable that this want of proper proportions was the cause of his negative results. M. Vicat, in conclusion, points out the importance of these observations, -hydraulic lime never having been found in the calcareous formation below the lias, is because the dolomites have never been examined, but it is now probable it may be found in this lower formation. L'Institut, No. 153., and Lond. and Ed. Phil. Mag. Liquefaction of Sulphuretted Hydrogen. Mr. Kemp discovered a very beautiful process for the liquefaction of sulphuretted hydrogen: he found that if dry persulphuretted hydrogen be introduced into a liquefying-tube, it slowly resolves itself into liquid protosulphuretted hydrogen, whilst sulphur in crystals is deposited. If previously there has been introduced into the end of the tube iodine in a dry state, then the protosulphuretted hydrogen, when it comes over upon it, dissolves it rapidly, and a dark yellowish brown coloured liquid results. If now to this there be added the least pos sible proportion of water (which is accomplished by a peculiar bend in the tube), instant reaction takes place, sulphur is deposited, and hydriodic acid in a most condensed and liquid state results. It is only necessary that a trace of water be present to commence the decomposition of the former brown compound, which I suppose to be the hydrosulphuret of iodine; for when this once commences, it goes on to any extent, and the liquid hydriodic acid formed may be called almost anhydrous. It boils by the heat of the hand like other condensed gases; it is of a yellowish colour, and resembles somewhat liquefied chlorine. Lond. and Edin. Philos. Mag. Experimental Researches in the laws of the motion of Floating Bodies. By J. S. RUSSELL. It was the object of these inquiries to assist in bringing to perfection the theory of Hydrodynamics, and ascertain the causes of certain anomalous facts in the resistance of fluids, so as to reduce them under the dominion of known laws. The resistance of fluids to the motion of floating vessels is found in practice to differ widely from theory, being, in certain cases, double or triple of what theory gives, and in other and higher velocities, much less. These deviations have now been ascertained to follow two simple and very beautiful laws: 1st. A law giving a certain emersion of the body from the fluid as a function of the velocity. 2nd. A law giving the resistance of a fluid as a function of the velocity and magnitude of a wave propagated through the fluid, according to the law of Lagrange. These two laws comprehend the anomalous facts, and lead to the following results: 1. That the resistance of a fluid to the motion of a floating body will rapidly increase as the velocity of the body rises towards the velocity of the wave, and will become greatest when they approach nearest to equality. 2. That when the velocity of the body is rendered greater than that due to the wave, the motion to the body is greatly facilitated: it remains poised on the summit of the wave in a position which may be one of stable equilibrium; and this effect is such that at a velocity of nine miles an hour the resistance is less than at a velocity of six miles behind the wave. Vibrations through Soil. - Cutting Veneers. 3. The velocity of the wave is independent of the breadth of the fluid and varies with the square root of the depth. 4. It is established that there is in every navigable stream a certain velocity at which it will be more easy to ascend the river against the current than to descend with the current. Thus, if the current flow at the rate of one mile an hour in a stream four feet deep, it will be easier to ascend with a velocity of eight miles an hour on the wave, than to descend with the same velocity behind the wave. 5. That vessels may be propelled on the summit of waves at the rate of between 20 and 30 miles an hour. Trans. Brit. Assoc. & Lond. and Edin. Philos. Mag. Communication of Vibrations through soil. By Capt. DENHAM. Capt. Denham ascertained that the vibrating effects of a passing laden rail road train in the open air extended laterally on the same level 1110 feet, (the substratum of the positions being the same,) whilst the vibration was quite exhausted at 100 feet when tested vertically from a tunnel. The tunnel was through a stratum of sandstone rock: the rails laid in the open air on a substratum of 12 feet of marsh over sandstone rock. The method of testing was by mercury reflecting objects to a sextant. The experiments were made in the neighborhood of Liverpool. Trans. Brit. Assoc., Lond. and Ed. Philos. Mag. Progress of Practical and Theoretical Mechanics and Chemistry. Cutting Veneers. Veneers used to be cut by the hand-saw; at present, the circular saw is, I believe, universally employed in England for this purpose, with the advantage not only of cheapness and expedition, but of a smaller waste of wood in saw dust, and of greater accuracy and precision in the thickness of the veneer-a quality essentially requisite to produce good work in the finished article. In a large veneer-mill which I had an opportunity, through the kindness of one of our members, of visiting, there are five circular saws. Each consists of a strong, stiff, circular frame-work, of the shape of a planoconvex lens, or rather a low hollow cone, tapering gradually to the edge, from which projects a ring of soft steel a few inches broad, pierced with many holes. The saw is a plate, or rather a flat ring, of well-tempered steel, about twelve inches broad, pierced with as many holes as the former ring, and firmly secured to it by means of screws: a band over the axis of the saw communicates motion to it, by connecting it with the first mover, which is a steam engine. The wood to be cut is laid on the cross-bars of a frame, which are previously covered with glue, and remains in a horizontal position, loaded with heavy weights, till the glue has become dry. The frame, with the log, or flitch, as it is technically called, adhering to it, is then fixed sideways in a carriage which traverses backwards and forwards, the frame itself being likewise capable of motion at right angles to the run of the carriage, in order to project the log sufficiently to bring it within the action of the saw. The quantity of the latter motion is regulated by a screw, one turn of which throws forward the frame, and, consequently, the log, about ㅎ of an inch. The saw being put in motion, the workman first turns the regulating screw more or less, according to the required thickness of the veneer; he then, by pulling a lever, throws the apparatus into gear, which gives motion to the carriage, and takes his seat by the inner, or convex, side of the saw. As soon as the log comes up to the saw, he directs the head of the veneer into a curved frame, which it readily enters, on account of its flexibility, being so very thin, and then employs himself in holding in each hand a chip of wood obliquely against the teeth of the screw, in order to clear them of the particles of saw dust which otherwise would more or less clog up. In a minute or two the log has passed the saw, the motion of the carriage is reversed, and it is brought back to the point from which it first started. Being then thrown out of gear, the regulating screw is again turned, to project the log as much as the intended thickness of the next veneer; and then all those motions are repeated which I have already described. The usual thickness of a veneer is about of an inch; but some kinds of wood may be cut as thin as about 1 of an inch. About half the wood is converted into saw dust.. 16 1 12 Of the fine saws employed at these mills, the largest is eighteen feet in diameter, and makes thirty revolutions in a minute. Three are each ten feet in diameter, with a speed of about sixty revolutions in a minute; the small saw is six feet in diameter, with a speed of eighty revolutions in a minute, which is sometimes increased to one hundred, or even one hundred and twenty revolutions. The teeth of the saws are nearly a quarter of an inch deep. A saw lasts about a year; for the first six months it is employed in coarse work, and afterwards, till worn out, in fine work. The veneer is necessarily split, for an inch or two at its head, in getting it on the curved frame; and as it is likewise liable to split in drying, a thin strip of linen is glued along the two cross edges of each veneer, which prevents this accident: the holes, at least those of an inch or more across, are also covered in the same manner. The general method of laying down veneers is very simple, although to do this well and correctly, requires, as every thing else does, practice, attention, and patience. The under side of the veneer, if previously smooth, must be scored by means of a toothing-plane; but if cut by a circular saw, it generally acquires a sufficient tooth by that operation. The surface to be veneered is covered over with strong glue, and before it chills or gelatinizes, the veneer, previously prepared and cut to the shape required, is laid down upon it, care being taken in doing so, to enclose as little air as possible. When it has heen pressed down to its proper bearing in every part, the compound piece is enclosed between two hot boards, secured at the edges by thumb screws, or, which is still better, is put into a press between two hot plates, where it remains till perfectly dry.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- in_burke