Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 11 (1833), p. 390 · View the page
(See specification at p. 111.) 47. For an improvement in the mode of Drilling and boring out the Wheels of Rail-road Cars; Dean Walker, Franklinville, Baltimore county, Maryland, December 28.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 11 (1833), p. 397 · View the page
The patentee is a manufacturer of stoves, and other articles of that description, and is familiar with the various plans of warming public and private buildings with heated air, as practiced in Philadelphia, where much has been done in this way; in many cases with considerable success, but in others, expectation has been entirely disappointed, after the expenditure of much money. In a heated air stove in a private house, it is stated that a quarter of a ton of coal was sometimes burnt in a day, without deriving sufficient heat from it to warm the building. On examination it was found that the heated air, after ascending five stories, escaped at a temperature of no less than $70° Fah. This, no doubt, was an extreme case of waste, but, in general, the quantity of heat, and consequently of fuel, lost, is very great. With Mr. Steinhauer's apparatus, the temperature of the smoke and gas escaping from the chimney, has been found to be but a few degrees above that of the surrounding atmosphere. Hot air chambers, on the ordinary construction, have been altered upon the plan of Mr. S., and the effect of the furnace in many instances doubled, without disturbing the original fixtures. Specification of a patent for an improvement in the mode of drilling and boring out the Wheels of Rail-road Cars. Granted to DEAN WALKER, of Franklinville, Baltimore county, Maryland, December 28, 1832.
Remarks. To all whom it may concern, be it known, that I, Dean Walker, of Franklinville, in the county of Baltimore, and state of Maryland, WALKER'S mode of Boring Wheels. have invented an improved mode of drilling, or boring out, the wheels of rail-road cars, so as to centre them perfectly on the axles; and also in the mode of drilling the pin holes by which they are afterwards attached to the said axles, and that the following is a full and exact description thereof. The machinery which I use for these purposes, resembles, in its general construction, the slide, or rack lathe, well known to machinists, and my invention consists in such an arrangement and adaptation thereof, as fits it to the particular purpose to which I apply it. The mandril of the lathe by which the wheels are bored out, is made hollow, so that the cylindrical shaft which carries the cutters may slide into it to a depth equal to that of the bored part of the wheel. The wheel is to be centred upon a plate affixed to the mandril, to which I attach it, whilst boring, by means of nuts and screws, or otherwise. The lathe may be driven by a whirl on a shaft which carries a pinion taking into a toothed wheel on the mandril, so proportioned to each other as to produce the proper degree of speed, or in any other way producing the same effect. The cylindrical shaft, carrying the bits, is sustained upon a slide in front of the mandril, its inner end passing through the part of the wheel to be bored, and into the cavity of the mandril prepared for its reception. The cutters are held in mortices in the shaft; of these there are two sets; the first, of a proper size for boring through the wheels, the second, placed behind the former, to face the wheel as the first passes through. The cylindrical shaft, with its bits, are made to advance by means of a rack and pinion, to which motion is given from the revolving mandril. Instead of a rack and pinion, however, a screw, or other contrivance, may be employed, so as to force the slide and cutters forward, by force, or power communicated to them from other parts of the machinery. After the wheels have been put upon the axles, a machine very similar to the former is used for drilling the holes to receive the pins which attach them to each other; the above described mandril, however, not being employed. I usually drill the holes at both ends of the axle at the same time, for which purpose the machine is made double. The ends of the axles, which pass through the wheels, rest on boxes fixed upon benches which sustain the slides carrying the drills. The mandril, or shaft, which receives the drill runs in collars like those of a lathe mandril, and is made to revolve in the same way. The slides are made to advance by means similar to those described for forcing forward the boring shaft, in the first mentioned machine.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- in_burke