Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 8 (1831), p. 174 · View the page
87. For an improvement upon a Water Wheel for propelling Boats, for which a patent was obtained on the 22nd day of December, 1818; Asa Waters, Millbury, Worcester county, Massachusetts, April 30.
Remarks. The buckets are made to swivel upon pins on their ends, working in arms. There are cams for locking and unlocking them, the intention being that the buckets may "always strike the water at a proper angle for obtaining most power, and have no back water to raise; because, when the buckets are brought to a certain position or bearing in the water, the cams at the bottom of the wheel press on the levers and unlock the floats, and let them swing loose on their pivots; and at the same time the floats at the top are locked by the same means; thus producing a maximum of power in the wheel." We have not heard that the wheel, as first patented, has been brought into successful operation; nor do we anticipate that with the improvements it will make its way as well as the common paddle wheel. We expect but little from swinging buckets in general.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 8 (1831), p. 180 · View the page
Instead of water, steam may be applied at the same temperatures, for the same length of time, and will answer the same purpose; but in this case the cloth must be wound around a revolving roller, or cylinder, which must be kept continually in motion during the process, and the steam must be confined by a wooden box, made very tight, so as to include the rollers, or cylinders, with the cloth upon them, within it. The cloth is to be taken out and cooled in the same way as when heated by water. The operations above mentioned render the cloth very firm in the bottom, divest it of wrinkles and cockles, or drawn places, and render it even and smooth on the sur* Some weeks will probably elapse between the date of this patent and that which will be next issued, as, in consequence of the absence of the Attorney General, the signature of that officer cannot be obtained, and without this a patent would not be valid. GIRAUD'S Spiral Lever for Propelling Vessels. face, so that the teazles, or points, may act uniformly upon the cloth, and the fibre of the wool, or cloth, is thus rendered more pliable, and is more easily turned and laid straight and smooth in the process of teasing, or raising the pile, or nap, thereon. And I, the said Cook, do hereby expressly declare, that all that I claim as new, and of my invention, or discovery, is the subjecting the cloth to the process aforesaid, in the manner aforesaid, and for the purposes aforesaid, after the same has been fulled, and before the pile, or nap, has been raised thereon by the process of teasing. CALVIN W. Соок. Specification of a patent for a Screw or Spiral Lever, for the propelling of Vessels, for a new mode of Navigation. Granted to JOHN JAMES GIRAUD, M. D., city of Baltimore, Maryland, April 27, 1831.
Remarks. INSIDE of a paddle water wheel, or frame, having a round hole in the centre, I place upon two sides, a screw, or spiral lever, threefourths, more or less, the diameter of the said paddle wheel; this screw, or lever, to be two or more turns of the spiral: this screw lever will be attached to two self acting fulcrum levers in the following manner. The ends of the levers, where are placed the fulcrum, are fixed, the one opposite to the other by their fulcrum, upon the edge inside of the paddle wheel, the one below, the other above, and distant a few inches from a straight line; the two other ends of the lever are fixed to a square piece of a few inches, with a round hole in the centre, placed in the middle of the paddle wheel; the end of the centre of the screw or spiral lever, is fixed on the side of the end of the lever, which is fixed on the side of the square piece, and the other end, which is made the end of the screw or spiral lever, is fixed upon the other lever, and near the fulcrum. I place upon the screw or spiral lever, a solid round wheel, twice the diameter of the paddle wheel, with a round hole in the centre, and fixed in the middle upon the square piece above mentioned. This solid wheel has two bars, one opposite the other, which project from its edges, coming level with the edge of the paddle wheel, one below, the other above, without touching it, a little distant from a direct line; place upon the ends of the bars a self acting fulcrum lever, by their fulcrum; the other ends of the lever to pass a little over the hole in the centre of the solid wheel:-a square piece of a few inches, having a square hole in the centre, will be placed between the two ends of the levers, to touch, yet leaving it free. A smaller screw or spiral lever will be placed and fixed to the ends upon the side of the end of the lever, which touches the square piece; and the other end of the screw to be fixed upon the other lever near to the edge of the solid wheel; the same thing to be done upon the other side of the paddle wheel. The shaft of the paddle wheel is square GIRAUD'S Spiral Lever for Propelling Vessels. in the middle, and round at each end: the shaft is placed in the holes of the two square pieces, and the power is conveyed there. I claim the principle of my invention and improvement in every species of levers, and of every form, and figure, and application, as above described. J. J. GIRAUD. Dr. John James Giraud's Self-acting Fulcrum Screw or Spiral Lever, for propelling Vessels and Rail-road Carts, &c. &c. Fig. 1. Fig. 2. A C B e C d Fig. 3. B A B B B Fig. 1.-A. The inside of one side, or part of the water paddle wheel. B. Screw, or spiral lever. c, c. Self-acting fulcrum levers. d, d. The fulcrum. e. The square piece with round holes. Fig. 2.-A. Solid wheel with round hole in the centre. B, B. Projecting bars with square holes. Fig. 3.-B, B. Self-acting fulcrum levers. c, c. The fulcrums. d. The screw, or spiral lever. e. The square piece with square hole. f. f. The moving bars. Fig. 2 is to be placed upon Fig. 1, and Fig. 3 upon Fig. 2.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- in_burke