Drawings and documents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 7 (1831), p. 369 · View the page
11. For a Reaction Water Wheel, for impelling saw mills and other works; Joseph C. Strode, East Bradford Township, Chester county, Pennsylvania, February 8.
Remarks. (See the specification.)
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 7 (1831), p. 381 · View the page
The churn is the common dasher churn, the rod of which is to be worked up and down by a pendulum. A frame is to be made, across the upper part of which there is to be a shaft turning upon gudgeons; from this hangs a weighted pendulum. The shaft is crossed by a lever, one end of which is attached to the dasher rod; from the other a pitman descends to a treadle. The pendulum may be made to vibrate by the hand; or the foot may be placed upon the treadle for the same purpose. The claim is to "the application of the pendulum principle to the dasher, which equalises the power applied, and assists in passing the reacting points in the rise and fall of the dasher; and also in the application of the foot power, which relieves the arms and chest in the act of churning." We apprehend that this machinery would be improved by removing the frame, the shaft, the pendulum, the pitman, and the treadle, and taking hold of the dasher by the hands, as dairy maids have been in the practice of doing from time immemorial. SPECIFICATIONS OF AMERICAN PATENTS. Specification of a patent for a Machine for Impelling Saw Mills and other works by water, called Strode's Reaction Wheel. Granted to JOSEPH C. STRODE, Teacher, East Bradford, Chester county, Pennsylvania, February 8, 1831.
Remarks. THERE is a wooden shaft seven feet six inches long, sixteen inches in diameter at the larger end, and fourteen at the smaller; in the centre of this shaft, is made a round hole eight inches in diameter at the larger end, and six at the other; the area of this hole will vary directly as the power required, and inversely as the subduplicate ratio of the height of the head above the centre of the shaft. a, a, a, a, are six hollow arms, six inches in diameter, set perpendicularly in the shaft, A, at equal angular and linear distances, forming a true spiral curve from one end to the other. The holes through these arms are three and a half inches in diameter. Near the end of each arm is a hole one and three-quarters inch in diameter, so situated that the axis of the shaft, A, is perpendicular to the plane passing through the axis of the hole and that of the arm, and so that a plane passing through the axis of the hole perpendicular to the aforesaid plane, shall be a tangent to the circle formed by the middle point in the axis of the hole, by the revolution of the machine on its axis. The distance of the centre of this hole from the centre of the shaft, is thirty-three inches, and will vary directly as the power required and the subduplicate ratio of the height of the head above the centre of the shaft, A, and inversely as the number of revolutions desired. The area of the hole will vary inversely as the subduplicate ratio of the height of the head, and directly as the power required. The distance between each two of the planes passing through the axis of the arms to which the axis of the shaft, A, is perpendicular, is eleven inches, and will not answer to be nearer, because the water from each arm nearer the larger end would impinge against the back of the next arm, and thereby impede its motion; so that if the number of arms be increased, the length of the shaft must be increased in proportion. The arms are made fast in the shaft by means of a tennon with a dovetail, as represented by figure H, the side of the tennon on which the dovetail is made is rather narrower than the opposite side, and the mortise in the shaft is of the same shape, so that when the wedge, I, is driven in on the side opposite to the dovetail, it will be firm and tight on all sides. B, is a hollow cylinder eight inches in length with a rim on one end, one inch and a quarter wide, and three-quarters of an inch thick. The diameter of the hole is eight inches, the same as that in the shaft A. Its diameter from out to out is nine inches and a half, half its length; the other half, or the part h, is nine inches and a quarter at the shoulder where g terminates, tapering to the end, where it is nine inches. This cylinder is let through the plank, STRODE'S Reaction Wheel. D, of the trunk, which is three inches thick, with its rim on the inside, which is sunk in the plank three-quarters of an inch deep, or so as to face with the inside of the plank. It is made at the same time firm and water tight by means of eight screw bolts, each three inches and a half long, driven in from the outside through holes made in the rim, where it is screwed up firmly and rendered tight by means of burs. The part h, is four inches in length, and goes into the cylinder, F, which is of the same length, and is made fast in the shaft. It has four wings to keep it from turning. This cylinder is of such a capacity that it will work easily on the part h, and at the same time not allow too much play. G, is a lead washer one inch and a quarter wide, three-eighths of an inch thick, and its inner diameter eight inches. This washer and an iron follower of the same dimensions, are screwed against the ends of h and F, (which are turned so as to face exactly,) by means of eight screws going through them and securing into the end of h. This is in order to render them water tight. B, is a cast iron friction wheel, fourteen inches in diameter, running with its periphery, which is turned true, against the iron band F, on the shaft, (the band being also turned,) thereby supporting the weight of the shaft, A, to prevent too much friction on the gudgeon, h, of figure E. The gudgeons of the friction wheel run on the middle of the two cross pieces, d and e, made of wood, which are supported by the upright pieces, b, b, of plank, two inches thick, spiked at the bottom to the sill, C, and made firm at the top by the inch board, c, going across from one to the other and nailed to each. In the foregoing description are given the dimensions of a machine now in operation, for impelling a saw mill under a head of twenty feet. If a larger or smaller wheel is required, the dimensions of the several parts will vary according to the proportions given.
About this record
- Patentee
- the Journal of the Franklin Institute, Journal
- Date
- the Name and Date index of patents, USPTO records, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The index's second listing was used.
- The patentee's full name comes from the Franklin Institute's journal.
- The residence comes from the Franklin Institute's journal.
- in_burke