Drawings and documents
Published accounts: specification
Specification printed in the Journal of the Franklin Institute
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 88 ยท View the page
Text of the specification as printed in the Journal, from OCR; not proofread.
Specification of a patent for an improvement in that part of the Ingrain Carpet Loom, which is called the Engine. Granted to JoSIAH R. CLARK, South Coventry, Tolland county, Connecticut, May 7th, 1830. THIS improvement consists in substituting a rotary sheet of pasteboard, parchment, painted canvass, or any other suitable substance, perforated with holes in such a manner as to form the figure required, in lieu of the barrel or cylinder with wire cogs, or staples, set in it, (somewhat resembling the barrel of a hand organ) which is commonly used; and also as a substitute for, and an improvement on " the Jay Card Machine," so called, or as it is sometimes called, "the Paper Machine;" and also as an improvement on the canvass apron with cogs or strips of wood attached to it, and with staples set in these cogs, which has been recently brought into use. The sheet of pasteboard, &c. required, will be of various size, according to the design of the figure to be laid out upon it, but always of a breadth about equal to the length of the cylinders, or cylinder, around which the sheet is to operate, and on this sheet is to be laid out the design for the figures to be woven by it in the same manner as the surface of the cylinder, or barrel, is usually laid out for the setting of the wire cogs, or staples; and in every place where a wire cog would be set in the cylinder, punch, or cut, a fair hole through the pasteboard; and all these holes in equi-distant lines across the pasteboard; and besides the holes which are laid out to form the figure, punch other holes near each edge of the pasteboard in about every second or third line of the figure holes. This sheet, being thus prepared, may be conveniently applied and used in the following manner, viz. place a small cylinder of any convenient diameter, and of such length as the work requires, say from twenty-one to thirty-eight inches long, in the same place, or nearly in the same place of the large barrel, or cylinder, commonly used; this small cylinder is to be fluted, or grooved, from end to end, with grooves about half an inch deep, and just as near together as the lines of holes across the pasteboard are; in every second or third groove, near each end of the cylinder, drive a pin of wire having a blunt point rising somewhat above the surface of the cylinder, and standing in right lines around it, like spur cogs, and exactly corresponding with the edge holes in the pasteboard. At a suitable distance behind this fluted cylinder, and parallel to it, place another plain cylinder; around both these cylinders wrap the sheet of pasteboard, and lace, or tack, the two ends together, or as nearly together as may be, in the manner of a rotary apron, or creeper, the rows of holes in the edges of which suit to the rows of pins in the fluted cylinder, and by which it is regularly moved forward and backward, in the same manner, and by similar machinery, to that which is in common use. In all " pointed," or "gathered" patterns, it is best to move the apron forward for the first half of the figure, and backwards for the reverse half; but in all "sprig," or "cumber" patterns, it is best to move the apron perpetually forward, in the same manner as is known and practised by all carpet weavers. In the barrel, or cylinder, engine, the pins or staples are so arranged, that the wire slides, commonly called "levers," which govern the threads of the warp, slide towards the cylinder at every "hard," or double throw of the shuttle, and a part of these slides, or levers, meeting with the pins, are obstructed in their course towards the centre of the barrel, and the number thus obstructed determines the number of threads of warp which shall be thrown over the surface of the web, from time to time, as the weaving progresses, to form the figures; and a cylinder, or barrel, with pins differently arranged, is requisite for each differently figured pattern. But this improvement is different, in that the levers, or slides, which meet with the holes through the foster-board, are permitted to pass inward by entering into the grooves in the smaller cylinder, and so determine the number and arrangement of the threads of the warp which shall be thrown upon the surface to constitute the figures. There are, however, not only several different substances which may answer nearly as well as pasteboard, but also several different arrangements not differing essentially from that more particularly described; especially, that instead of having the perforated apron pass round two cylinders in an elliptical form, as before described, VOL. VI. No. 2. -AUGUST, 1830. 12 : 1 1 it may be bound fast upon the surface of a large cylinder, grooved as aforesaid; the grooves being just as far apart as the rows or lines of holes in the apron; but in this arrangement there will be no need of so many holes at the edges as in the former case; and this cylinder may take the same place and be moved by the same machinery, and in the same manner, as the common barrel with pins in it is moved. In this arrangement, as well as the foregoing, the same cylinder continues always on the engine, and the coverings only are changed to operate all the variety of patterns. In fine, the only things which I claim as improvements are the rotary apron perforated so as to form the figure (upon principles already in use) as being much cheaper, more simple, more sure to be in order, more easily shifted, and requiring less attention in foremanship, than the barrel with pins, or staples, the canvass with staples, or any other method of forming the figures in carpet engines now in use; and also the fluted, or grooved cylinder, upon which the perforated apron operates. JOSIAH R. CLARK.
About this record
- Patentee
- Jim Shaw's X-patent list
- Date
- the Name and Date index of patents, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, Jim Shaw's X-patent list, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.