Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 64 · View the page
Transcription
Machine-read text of the specification as printed in the Mirror; not proofread. Check the page scan for figures, reference letters and spelling.
ee . IMPROVEMENT IN THE GRIST MILL ; Bes _ By William L. Taylor, of M’Minn county, Tennessee. See Plate VIII. ; ee Specification —Be it known, that I, William L. Taylor, of the : am county of M’Minn, and state of Tennessee, have invented or dis- Ri : covered a new and useful improvement, in the form, proportion and a application of the mill stone and band-wheel, for the manufacture of . corn, wheat, rye, and small grain of every description, into meal an or flour: also, for reducing plaster of Paris and other substances Ilia into powder, denominated “‘ The grooved or Rabited Extended AM ’ Horizontal Runner,” specified and described in the words folts lowing, viz: :
1. The runner is constructed of a size larger in diameter than Ne, the permanent, or bed stone, in the proportion. of about eight and aie seventy-five-hundredths, to six, or four feet, four and an half ee inches, to three feet; and in the same proportion for any other ie dimensions that circumstances may require; which proportion has been found, by experience, to be the best for the manufacgee Se ture of good flour, and is about the maximum to which the run- Hea: = ner can be increased without scorching, or injuring the flour, ies from the heat generated by its accelerated motion. A circular groove or rabit is to be formed in the runner, about a six inches (more or less) in perpendicular depth from its surface; on the under, or face side, including an area around the ig centre, in diameter, a little less than the diameter of the perma- wil ‘a nent, or bed stone. This groove is for the purpose of receiving the hoop which surrounds, and binds close upon the bed stone, ee and the flour trough to which it is attached. The imer side of a this groove, next to the centre, must be cut perpendicular to the Leal face of the runner. The outer side, to be levelled to an angle, . ta corresponding with that of the upper surface of the inclined flour . a trough, over which the runner must revolve freely, without comez ing in contact with it.
a 2. To the common wallower-shaft, must be affixed a number pay Samual of band wheels, of various sizes, in order that the velocity of __ the runner may be increased, or diminished, at pleasure, or as circumstances may require. These band wheels are to be connected with the main or power shaft, by means of a band of aa leather, or other suitable material, which is to pass overa driver, ae or drum placed upon that shaft, and the band whirls before described, and by which means motion is communicated to the wn eee Tanner.
te The great advantage to be gained, by increasing the diameter ie of the runner over that of the bed stone, must be too manifest to F aga every scientific and practical mind, to require comment; as it is Bees, self-evident, that the momentum of centrifugal force, will thereby SP Tee ee us) * Ps SF eae Pe in, eee ae he a ieee oY Pa be greatly augmented, the resistance by friction, so invariably experienced by the mechanician in the operation of all machines, diminished in an inverse ratio to the increase of force, and the quantum of work consequently augmented in a proportionate degree. By the introduction, too, of the band-whirls, in place of the wallower, in common use, it is believed that the friction will be considerably reduced. in, 1) a In the application of these two principles consists the improvement in the grist-mill, to which, as original inventor, I claim, for myself, my heirs, executors, administrators and assigns, the full and exclusive right and benefit, for the term of fourteen years, agreeably to the several acts of Congress, in such cases made and provided: and the principle is intended equally to embrace all posi- . tions in which mill stones of my construction may be placed, whether horizontally, perpendicularly, or obliquely. It is also intended to apply to all substances of which runners, upon my construction, may be formed; whether of stone, iron, or any other material. In testimony that the foregoing is a true specification or description of my said invention, improvement, or discovery, I do hereunto set my hand and seal, this eighth day of January, A. D. eighteen hundred and twenty-eight: WILLIAM L. TAYLOR.
JOHN M’GHEE, ‘ ee JOHN LOUDY, Date of patent, January 28,.1828. ” :
[References to the plate, as printed:]
REFERENCES.—PLATE VIII.
A Fig. 1. That part of the runner which meets the bed-stone. Fig. 1. The groove for the hoop, and flour trough. Fig. 1. That part of the runner which extends beyond the bed-stone. Fig. 2. Perpendicular section of the runner. Fig. 2. Perpendicular section of the bed-stone. Fig. 2. The groove for the hoop, and flour trough. Fig. 2. End view of sections of the iron bands. Fig. 2. The flour trough.
Fig. 2. The spindle.
Fig. 2. Band-whirls on the spindle.
Fig. 2. Trundle-head. ; :
Fig. 2. Cog-wheel.
Fig. 2. Band-whirls on cog-wheel shaft.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, vol. 5 (1828), p. 357 · View the page
In the grist mill; William L. Taylor, of M'Minn County, Tennessee, January 28.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The specification was printed in the Mirror of the Patent Office (1828).
- S. A. Elliot's printed list of patents gives the same name and date.
- in_burke